• MAP-ECU Man's Avatar
    12th-February-2019, 06:39 PM
    The lookup file is on the second post in this thread. Does it not work? The wiring is pretty simple and it depends on which MAPECU input you use. ...
    6 replies | 238 view(s)
  • MAP-ECU Man's Avatar
    11th-February-2019, 11:20 PM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    Most widebands work. Check out the wideband section of the forum for diagrams and lookup files.
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    10th-February-2019, 05:01 PM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    For tuning you have to have a external wideband setup. You cannot rely on the OEM wideband sensors, especially if you alter their output in closed...
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    10th-February-2019, 08:27 AM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    You will only see an AFR if you have a wideband connected to a MAPECU3 input configured to WB. You cannot get a AFR reading from the OEM sensors. ...
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    8th-February-2019, 09:16 PM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    Great, it starts and runs, well done! Have you configured the TPS input to “TPS”?
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    8th-February-2019, 09:14 PM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    Sorry about the delay responding, that sounds like a sensible idea so you can disconnect easily.
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    8th-February-2019, 09:13 PM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    Sounds like you worked it out, great.
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    1st-February-2019, 10:16 AM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    The wiring diagram you linked to on the forum in an earlier post is already wired for MAF Intercept. You will see the MAF input and MAF output wires...
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    31st-January-2019, 01:21 PM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    OK, no problem. Nothing wrong with having it in the mix for when you need it. I might need to clarify. Learn mode is *only* used for MAF...
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    31st-January-2019, 09:52 AM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    The AFR Calibrator does allow you to alter the AFR's the OEM sees in closed loop so you can run more rich in closed loop than normal. Generally this...
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    30th-January-2019, 09:34 AM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    Thanks for the base table and info. We have a few recommendations: If you are staying NA, then you shouldn't need the AFR Calibrator. That is...
    23 replies | 214 view(s)
  • MAP-ECU Man's Avatar
    29th-January-2019, 09:53 AM
    MAP-ECU Man replied to a thread General set up in Fuel Tables
    Welcome to the MAPECU Forum! :) I'll answer your questions below: It depends on the MAPECU3 mode, but assuming you are configured in MAF...
    23 replies | 214 view(s)
No More Results
About MAP-ECU Man

Basic Information

Signature


MAP-ECU Support

Statistics


Total Posts
Total Posts
6,547
Posts Per Day
1.47
General Information
Last Activity
12th-February-2019 06:40 PM
Join Date
24th-December-2006
Referrals
8